Sandwich Panel Roll Forming Machine, EPS Sandwich Panel Line, Mineral Wool Sandwich Panel line, Sandwich Panel Roll Forming Line
Sandwich panel production line is especially designed for producing insulation composite board. With stepless speed regulation system, it is able to produce corrugated composite panel efficiently at one time. Sandwich panel roll forming machine has been an indispensable device in fabricating roof panels and wall panels in plants and warehouses, among other buildings.
Features
1. The motor power of the sandwich panel roll forming line is 4kw, and the production speed reaches 6m/min. With the stepless speed regulation system, the efficiency of the roll forming line is optional within 0-6m/min.
2. When producing EPS sandwich panel, the speed is generally controlled at 2-6 m/min. It will be slightly lower for making rock wool board (depends on actual needs)
3. The composite panel production line is equipped with K-9 glue metering pump, featuring low rotating speed and high accuracy. The glue is fed at a rate of 0.1-2.0 kg/min. It is controlled by frequency converter.
4. The thickness of the composite panel the roll forming unit can produce is varied from 50mm to 250mm. By adjusting the upper and lower rack, and the distance between the cutter holder and the material feeding rack, we can get sandwich boards with different thickness and specifications.
5. Total installed capacity: 34KW; total weight (including accessories): 17.5t.
6. Dimension of the panel roll forming machine: 12500 (16000 for rock wool boards) X2200X2800; the roll former for 5 type EPS sandwich panel adopts 23 rubber shafts and 160X80 square tubes with thickness of 6mm; the roll former for 7 type composite rock wool panel employs 45 rubber shafts, and upper and lower independent glue supply. It is equipped with 1.7m rock wool panel conveyor belt, with the diameter of the drive shaft to be 50mm; length of the machine frame is up to 9m; the roll former is welded with 180X80 square tubes which thickness is 8mm.
Requirements for Factories:
The factories where our EPS sandwich panel production line are applied can be either flatroof or sloped-roof type. The height of the cornice should be larger than 5m, and the effective width should be at least 45m. The floor of the factory should be flat and concrete. For foundation of the roll forming line, it is required to be to be 380V, and the total installed power is 34kw. It is necessary for the factory to be equipped with 0.4-0.6MPa compressed air supply and illumination devices. The roll forming machine shares the same power supply with the auxiliary devices. The fluctuation of voltage should be no more than 10%, or it may lead to an abnormal running of the system.
The stroke is no less than 29m, the load for a lifting process is larger than 5000kg, and the lifting height is no less than 3.9m. For daily production and maintenance, about 6-10 people are needed, with 3-4 operators for some core processes included.
| Accessories List of 5 Type Composite Roof And Wall Cladding Panel Machine |
| adjust spanner |
3pieces |
| filter element |
2pieces |
| big glue head |
2pieces |
| bulkhead glue |
4pieces |
| glue joint |
4pieces |
| steel sheet chuck |
2pieces |
| screw |
depends |
| machine tool pad iron |
16sets |
| brake plate |
3 sets |
| M16×140 bolt |
16pieces |
| axes |
1piece |
| M16 nut |
16pieces |
| steel wire tube |
1piece |
| heating tube |
8pieces |
| heating tube ceramics end |
16sets |
| glue pipe |
6pieces |
| M8×35 inner hexagon screws |
30pieces |
| φ10×80 taper pin |
1piece |
| delivery rack |
1set |
| mainframe |
1set |
| cutting rack |
1set |
| tile plate wheel |
1set |
| overtravel-limit switch |
2pieces |
| pneumatic elements |
1 set |
| glue channel(4long 2short) |
6pieces |
| large tray |
1piece |
| ladder |
1piece |
| M16×40 outer hexagon screws |
8pieces |
| Color clip |
4 sets |
| discharge rack |
1piece |
| 05-06 frame |
1set |
| rod |
12pieces |
| 00 frame |
1piece |
| hanger |
1piece |
| 4 m foam holder |
4pieces |
| long cylinder |
1piece |
| clip lock lever |
2pieces |
| bourdon spring |
1piece |
| 1220 roller |
8pieces |
| roller axes |
16pieces |
| 6004 bearing |
16sets |
| M20 nut |
24pieces |
| cutting under frame |
1 piece |
contact with Roy Gao to discuss the order,
0086 159 3271 2693
Sandwich Panel Roll Forming Machine
Sandwich Panel Roll Forming Line
Eps Sandwich Panel Line
Mineral Wool Sandwich Panel Line
Sandwich Panel Roll Former
Composite Panel Roll Forming Line
Audited Supplier 
){kind=link}
){kind=link}